Ürünler

Pepperl Ultrasonik Sensörler
Endüktif Sensör Pepperl Fuchs NBB15-U10-E2-25M
Ultrasonic Sensor Pepperl Fuchs
Endüktif Sensör Pepperl Fuchs NBB15-U1K-N0
Tümünü Göster
Pepperl Fuchs Ultrasonic Sensor

Endüktif Sensör Pepperl Fuchs NBB15-U1K-E2-3G-3D

Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NBB15-U1K-E2-3G-3D
Pepperl NBB15-U1K-E2-3G-3D
NBB15-U1K-E2-3G-3D

Kategoriler: , Etiketler:
Açıklama

Pepperl Fuchs NBB15-U1K-E2-3G-3D Endüktif Sensör
Pepperl NBB15-U1K-E2-3G-3D Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NBB15-U1K-E2-3G-3D
Pepperl Fuchs NBB15-U1K-E2-3G-3D Yakınlık Sensörü
Inductive Sensor NBB15-U1K-E2-3G-3D Pepperl-Fuchs
Endüktif Sensör NBB15-U1K-E2-3G-3D Pepperl-Fuchs

Teknik veriler NBB15-U1K-E2-3G-3D

General specifications
Switching functionNormally open (NO)
Output typePNP
Rated operating distance15 mm
Installationflush
Output polarityDC
Assured operating distance0 … 12.15 mm
Actual operating distance13.5 … 16.5 mm typ. 15 mm
Reduction factor rAl0.33
Reduction factor rCu0.3
Reduction factor r3040.74
Reduction factor rBrass0.41
Output type3-wire
Nominal ratings
Operating voltage10 … 30 V
Switching frequency0 … 200 Hz
Hysteresistyp. 5 %
Reverse polarity protectionreverse polarity protected
Short-circuit protectionpulsing
Voltage drop≤ 2 V
Voltage drop at IL
Voltage drop IL = 1 mA, switching element on0.5 … 2.3 V typ. 0.9 V
Voltage drop IL = 10 mA, switching element on0.8 … 2.2 V typ. 1.4 V
Voltage drop IL = 20 mA, switching element on0.9 … 2.3 V typ. 1.5 V
Voltage drop IL = 50 mA, switching element on0.9 … 2.5 V typ. 1.6 V
Voltage drop IL = 100 mA, switching element on1 … 2.6 V typ. 1.8 V
Voltage drop IL = 200 mA, switching element on1.2 … 2.8 V typ. 2 V
Operating current0 … 200 mA
Off-state current0 … 0.5 mA typ. 0.01 mA
Off-state current TU =40 °C, switching element off≤ 100 µA
No-load supply current≤ 20 mA
Time delay before availability80 ms
Operating voltage indicatorLED, green
Switching state indicatorLED, yellow
Functional safety related parameters
MTTFd1242 a
Mission Time (TM)20 a
Diagnostic Coverage (DC)0 %
Compliance with standards and directives
Standard conformity
StandardsEN 60947-5-2:2007
EN 60947-5-2/A1:2012
IEC 60947-5-2:2007
IEC 60947-5-2 AMD 1:2012
Approvals and certificates
FM approvalhazardous (classified) location
Non-incendive
UL approvalcULus Listed, General Purpose
CCC approvalCCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature-25 … 85 °C (-13 … 185 °F)
Mechanical specifications
Connection typeConnector plug M12 x 1 , 4-pin
Information for connectionA maximum of two conductors with the same core cross section may be mounted on one terminal connection!
tightening torque 1.2 Nm + 10 %
Core cross-sectionup to 2.5 mm2
Minimum core cross-sectionwithout wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2
Maximum core cross-sectionwithout wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2
Housing materialPA
Sensing facePA
Degree of protectionIP68 / IP69K
Mass225 g
NoteTightening torque: 1.8 Nm (housing)
Equipment protection level Gc (nA)
CertificatePF 15CERT3754 X
CE marking[*PD-Z02586A*]
ATEX markingII 3G Ex nA IIC T6 Gc
The Ex-related marking can also be printed on the enclosed label.
StandardsEN 60079-0:2012+A11:2013, EN 60079-15:2010
Ignition protection category “n”
Use is restricted to the following stated conditions
Special conditions
Maximum operating current ILThe maximum permissible load current must be restricted to the values given in the following list. High load currents and load short-circuits are not permitted.
Maximum operating voltage UBmaxThe maximum permissible operating voltage UB max is restricted to the values in the following list. Tolerances are not permissible.
Maximum permissible ambient temperature TUmaxdependant of the load current IL and the max. operating voltage UBmax
Information can be taken from the following list.
at UBmax=30 V, IL=200 mA50 °C (122 °F)
at UBmax=30 V, IL=100 mA53 °C (127.4 °F)
at UBmax=30 V, IL=50 mA54 °C (129.2 °F)
Equipment protection level Dc (tc)
CE marking[*PD-Z02586A*]
ATEX markingII 3D Ex tc IIIC T80°C Dc
The Ex-related marking can also be printed on the enclosed label.
StandardsEN 60079-0:2012+A11:2013, EN 60079-31:2014
Protection by enclosure “tc” Some of the information in this instruction manual is more specific than the information provided in the datasheet.
GeneralThe corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
Special conditions
Maximum permissible ambient temperature TUmaxdependant of the load current IL and the max. operating voltage UBmax
Information can be taken from the following list.
at UBmax=30 V, IL=200 mA50 °C (122 °F)
at UBmax=30 V, IL=100 mA53 °C (127.4 °F)
at UBmax=30 V, IL=50 mA54 °C (129.2 °F)

İlgili ürünler

Top