Endüktif Sensör Pepperl Fuchs NJ60-FP-E2-P2-V1
Endüktif Sensör Pepperl Fuchs NJ8-18GK-N
Endüktif Sensör Pepperl Fuchs NJ6S1+U1+N1
Sensör
Yakınlık Sensörü
Proximity Sensor
Endüktif Proximity Sensör
Inductive Proximity Sensor
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Proximity Sensor
Pepperl Fuchs Yakınlık Sensörü
Pepperl Fuchs Endüktif Proximity Sensör
Pepperl Fuchs Inductive Proximity Sensor
Pepperl Fuchs NJ6S1+U1+N1
Pepperl NJ6S1+U1+N1
NJ6S1+U1+N1
Açıklama
Pepperl Fuchs NJ6S1+U1+N1 Endüktif Sensör
Pepperl NJ6S1+U1+N1 Inductive Sensor
Yaklaşım Sensörü Pepperl Fuchs NJ6S1+U1+N1
Pepperl Fuchs NJ6S1+U1+N1 Yakınlık Sensörü
Inductive Sensor NJ6S1+U1+N1 Pepperl-Fuchs
Endüktif Sensör NJ6S1+U1+N1 Pepperl-Fuchs
Teknik veriler NJ6S1+U1+N1
| General specifications | ||
| Switching function | Normally open (NO) | |
| Output type | NAMUR with safety function | |
| Rated operating distance | 6 mm | |
| Installation | flush | |
| Assured operating distance | 0 … 4.86 mm | |
| Reduction factor rAl | 1 | |
| Reduction factor rCu | 1 | |
| Reduction factor r304 | 0 | |
| Output type | 2-wire | |
| Nominal ratings | ||
| Nominal voltage | 8.2 V (Ri approx. 1 kΩ) | |
| Switching frequency | 0 … 100 Hz | |
| Current consumption | ||
| Measuring plate not detected | ≤ 1 mA | |
| Measuring plate detected | ≥ 3 mA | |
| Functional safety related parameters | ||
| Safety Integrity Level (SIL) | SIL 3 | |
| MTTFd | 9191 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| NAMUR | EN 60947-5-6:2000 IEC 60947-5-6:1999 | |
| Approvals and certificates | ||
| FM approval | ||
| Control drawing | 116-0165 | |
| UL approval | cULus Listed, General Purpose | |
| CSA approval | cCSAus Listed, General Purpose | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 … 100 °C (-13 … 212 °F) | |
| Mechanical specifications | ||
| Connection type | screw terminals | |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % | |
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | PBT | |
| Sensing face | PBT | |
| Degree of protection | IP68 | |
| Note | only for non-ferrous metal | |
| Data for application in connection with hazardous areas | ||
| Equipment protection level | Ga , Gb , Da , Mb | |
| General information | ||
| Use in the hazardous area | see instruction manuals | |
