Ultrasonik Sensör Pepperl Fuchs UC2000-30GM-IU-V1-HB
Ultrasonik Sensör Pepperl Fuchs UC2000-30GM-IUR2-T-V15
Ultrasonik Sensör Pepperl Fuchs UC2000-30GM-IUEP-IO-V15
Sensör
Ultrasonic Sensor
Ultrasonik Sensör
Pepperl Fuchs
Pepperl Fuchs Sensör
Pepperl Fuchs Ultrasonic Sensor
Pepperl Fuchs Ultrasonik Sensör
Pepperl Fuchs UC2000-30GM-IUEP-IO-V15
Pepperl UC2000-30GM-IUEP-IO-V15
Açıklama
Pepperl Fuchs UC2000-30GM-IUEP-IO-V15 Ultrasonik Sensör
Pepperl UC2000-30GM-IUEP-IO-V15 Ultrasonic Sensor
Teknik veriler UC2000-30GM-IUEP-IO-V15
| Ürün Açıklaması |
| Single head system |
| General specifications | ||
| Sensing range | 90 … 2000 mm | |
| Adjustment range | 120 … 2000 mm | |
| Dead band | 0 … 90 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 200 kHz | |
| Response delay | minimum : 65 ms factory setting: 125 ms | |
| Indicators/operating means | ||
| LED green | solid: Power on flashing: Standby mode or IO link communication | |
| LED yellow 1 | solid: Object in evaluation range flashing: Learning function, object detected | |
| LED yellow 2 | solid: Object in evaluation range flashing: Learning function, object detected | |
| LED red | solid red: Error red, flashing: program function, object not detected | |
| Electrical specifications | ||
| Operating voltage | 10 … 30 V DC , ripple 10 %SS 15 … 30 V voltage output | |
| No-load supply current | ≤ 60 mA | |
| Power consumption | ≤ 1 W | |
| Interface | ||
| Interface type | IO-Link | |
| Protocol | IO-Link V1.0 | |
| Transfer rate | Acyclical: typical 95 Bit/s | |
| Cycle time | min. 33.6 ms | |
| Process data witdh | 16 bit | |
| SIO mode support | yes | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 … 1 V | |
| 1 Level | 4 V … UB | |
| Input impedance | > 12 kΩ | |
| Output rated operating current | < 12 mA | |
| Pulse length | 0.5 … 300 ms (level 1) | |
| Pulse interval | ≥ 33 ms (level 0) | |
| Synchronization frequency | ||
| Common mode operation | ≤ 30 Hz | |
| Multiplex operation | ≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ) | |
| Output | ||
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA … 20 mA or voltage output 0 V … 10 V configurable | |
| Rated operating current | 200 mA , short-circuit/overload protected | |
| Voltage drop | ≤ 2.5 V | |
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm | |
| Deviation of the characteristic curve | ≤ 0.2 % of full-scale value | |
| Repeat accuracy | ≤ 0.1 % of full-scale value | |
| Switching frequency | ≤ 4 Hz | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable | |
| Load impedance | current output: ≤ 300 Ohm voltage output: ≥ 1000 Ohm | |
| Temperature influence | ≤ 1.5 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation) | |
| Approvals and certificates | ||
| UL approval | cULus Listed, General Purpose | |
| CSA approval | cCSAus Listed, General Purpose | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) | |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 5-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | Stainless steel 1.4305 / AISI 303 TPU Polyamides | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Mass | 72 g | |
